GRACO MAGNUM 309045K INSTRUCTIONS MANUAL Pdf Download (2024)

GRACO MAGNUM 309045K INSTRUCTIONS MANUAL Pdf Download (1)
  1. Manuals
  2. Brands
  3. Graco Manuals
  4. Paint Sprayer
  5. Magnum 309045K
  6. Instructions manual

GRACO MAGNUM 309045K INSTRUCTIONS MANUAL Pdf Download (2)

Airless spray guns

Hide thumbs

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Advertisement

Quick Links

Download this manual

Instructions

SG2, SG3 Airless Spray Guns

Pistolets pulvérisateurs sans

air SG2, SG3

– For applying architectural paints and coatings –

3600 psi (248 bar, 25 MPa) Maximum Working

Pressure

Pression de service maxi 3600 psi (248 bars, 25

MPa)

SG2 Model 243011, A

Modèle SG2 243011, A

Reversible Tip Guard, 515 Tip, RAC IV

Garde-buse réversible, buse 515, RAC IV

SG3 Model 243012, A

Modèle SG3 243012, A

Reversible Tip Guard, 515 Tip, RAC IV

Garde-buse réversible, buse 515, RAC IV

SG3 Model 246506, A

Modèle SG3 246506, A

Reversible Tip Guard, 515 Tip, RAC 5

Garde-buse réversible, buse 515, RAC 5

SG3–E Model 243238, A

Modèle SG3–E 243238, A

Reversible Tip Guard, 515 Tip

Garde-buse réversible, buse 515

SG3–A Model 243382, A

Modèle SG3–A 243382, A

Reversible Tip Guard, 515 Tip

Garde-buse réversible, buse 515

All models not available in all countries

Tous les modèles ne sont pas disponibles dans tous les

pays

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

Instructions de sécurité importantes.

Lire toutes les mises en garde et

instructions de ce manuel. Sauvegarder

ces instructions.

243012

309045K

NextPage
  • 1
  • 2
  • 3
  • 4
  • 5

Advertisement

GRACO MAGNUM 309045K INSTRUCTIONS MANUAL Pdf Download (3)

Related Manuals for Graco Magnum 309045K

  • (37 pages)

  • Paint Sprayer Graco SG2 Instructions Manual

    Airless spray guns (22 pages)

  • Paint Sprayer Graco SG3 Instructions Manual

    Airless spray gun (14 pages)

  • Paint Sprayer Graco 243012 Instruction Manual

    Sg3 airless spray guns (8 pages)

  • Paint Sprayer Graco 243238 Instruction Manual

    Graco inc. airless spray guns instruction manual (8 pages)

  • Paint Sprayer Graco 243238 Instructions Manual

    Graco inc. airless spray guns instructions manual (8 pages)

  • Paint Sprayer Graco SG2 User Manual

    (4 pages)

  • Paint Sprayer Graco 16W431 Manual

    (4 pages)

  • Paint Sprayer Graco 17J910 Manual

    (4 pages)

  • Paint Sprayer Graco 243011 Manual

    Graco inc. spray guns instructions manual (4 pages)

  • Paint Sprayer Graco 309092F Instruction Manual

    Graco inc. silver airless spray gun instruction manual (12 pages)

  • Paint Sprayer Graco 309092 Instructions Manual

    Silver airless spray gun (10 pages)

  • Paint Sprayer Graco 246220 Instructions Manual

    Graco inc. spray gun instruction manual (24 pages)

  • Paint Sprayer Graco 309674M Repair Manual

    Electric airless sprayers, 3300 psi (227 bar, 22.7 mpa) maximum working pressure (33 pages)

  • Paint Sprayer Graco Fusion 2004230905 Instructions Manual

    Plural component, impingement mix mechanical purge spray gun (56 pages)

  • Paint Sprayer Graco Xtreme 309329 Operation Manual

    Graco inc. sprayer operation manual (26 pages)

Summary of Contents for Graco Magnum 309045K

  • Page 1 Instructions SG2, SG3 Airless Spray Guns Pistolets pulvérisateurs sans air SG2, SG3 – For applying architectural paints and coatings – 3600 psi (248 bar, 25 MPa) Maximum Working Pressure Pression de service maxi 3600 psi (248 bars, 25 MPa) SG2 Model 243011, A Modèle SG2 243011, A Reversible Tip Guard, 515 Tip, RAC IV Garde-buse réversible, buse 515, RAC IV...
  • Page 2 The following are general warnings related to the setup, use, grounding, maintenance and repair of this equipment. Additional, more specific warnings may be found throughout the body of this manual where applicable. Symbols appearing in the body of the manual refer to these general warnings. When these symbols appear throughout the manual, refer back to these pages for a description of the specific hazard.
  • Page 3 Les mises en gardes suivantes sont des mises en garde de sécurité relatives à la configuration, utilisation, mise à la terre, maintenance et réparation de ce matériel. D’autres mises en garde plus spécifiques figurent dans ce man- uel aux endroits concernés. Les symboles figurant dans ce manuel font référence à ces mises en garde générales. Quand vous voyez l’un de ces symboles dans le manuel, reportez–vous à...
  • Page 4 Grounding and Electric Requirements/Spécifica- É tions lectriques et de Mise à la Terre ti5850a 309045 The sprayer must be grounded. Grounding reduces risk of static and electric shock by providing an escape wire for the electrical current due to static build up or in the event of a short circuit. Het spuitapparaat moet worden geaard.
  • Page 5 Grounding and Electric Requirements/Spécifica- É tions lectriques et de Mise à la Terre ti5851a D Ground the metal pail by connecting a ground wire to the pail by clamping one end to pail and the other end to ground such as as water pipe. Raccorder le seau métallique à...
  • Page 6 Component Identification / Identification des composants Tip Guard / Protection de buse CAUTION / ATTENTION Tip / Buse 309045 Needle Adjustment / Réglage du pointeau Trigger / Gâchette Trigger Lock / Loquet de sécurité...
  • Page 7 PRESSURE RELIEF / DECOMPRESSION Follow 1–7 when you stop spraying. Suivre les étapes 1 à 7 lorsqu’on arrête de pulvériser. 1. Turn pressure to lowest setting. Turn sprayer OFF. Unplug. Régler la pression au minimum. Mettre le pulvérisateur sur ARRET. Débrancher. 2.
  • Page 8 309045 5. Trigger gun into grounded metal bucket. Actionner le pistolet en le tenant dans un seau métal- lique mis à la terre. 6. Set trigger lock. Verrouiller la gâchette. 7. Turn Prime/Spray valve to PRIME. Mettre la vanne Amorçage/Pulvérisation sur AMORÇAGE.
  • Page 9 ALIGN SPRAY / ALIGNER LE JET 1. Relieve Pressure, page 7. Décompression, page 7. 2. Loosen tip guard retaining nut. Desserrer l’écrou de fixation du garde-buse. 3. Turn tip guard horizontally to spray a horizontal pattern. Mettre le garde-buse à l’horizontale pour obtenir un jet horizontal.
  • Page 10 ADJUST SPRAY / RÉGLER LE JET 309045 1. Set trigger lock. Verrouiller la gâchette. 2. Install tip and guard. Monter la buse et la garde. 3. Tighten retaining nut. Resserrer l’écrou de retenue. 4. Remove trigger lock. Déverrouiller la gâchette.
  • Page 11 5. Trigger gun. Actionner la gâchette du pistolet. 6. Hold gun perpendicular and approximately 12 in. (304 mm) from surface. Move gun first, then pull gun trigger to spray. Tenir le pistolet perpendiculairement à la surface à peindre et à env. 12 in. (304 mm) de celle-ci.
  • Page 12 CLEAR CLOG / DÉBOUCHER 309045 1. Relieve Pressure, page 7. Décompression, page 7. 2. Set trigger lock. Verrouiller la gâchette. 3. Rotate tip 180_. Tourner la buse de 180_. 4. Remove trigger lock. Déverrouiller la gâchette.
  • Page 13 Trigger gun into pail or onto ground to remove clog. Actionner le pistolet dans un seau ou au-dessus du sol pour le déboucher. 6. Set trigger lock. Verrouiller la gâchette. 7. Rotate tip 180_. Tourner la buse de 180_. 309045...
  • Page 14 REPLACE NEEDLE / REMPLACER LE 309045 POINTEAU 1. Relieve Pressure, page 7. Décompression, page 7. 2. Set trigger lock. Verrouiller la gâchette. 3. Remove tip and guard and disconnect gun from fluid hose. Démonter la buse et la garde, puis dé- brancher le flexible produit sur le pistolet.
  • Page 15 OLD / ANCIEN 5. Squeeze trigger while unscrewing the diffuser. Presser la gâchette tout en dévissant le diffuseur. 6. Remove locknut and end cap. Retirer l’écrou de fixation et l’obturateur. 7. Tap out needle. Sortir le pointeau. 309045...
  • Page 16 CLEAN / NETTOYER SILICON SILICONE GREASE / GRAISSER NEW / NOUVEAU 309045 8. Clean internal passages of gun. Nettoyer les conduits intérieurs du pistolet. 9. Grease o–rings of new needle using a nonsilicon grease. Graisser les joints toriques du nouveau pointeau avec une graisse sans silicone.
  • Page 17 LOOSE / DESSERRER 26–32 ft–lb (19–24 N.m) 11. Install end cap and locknut, loosely. Mettre l’obturateur et l’écrou en place, sans serrer. 12. Grease o–rings of new needle using a non- silicon grease. Graisser les joints toriques du nouveau pointeau avec une graisse sans silicone. Grease / Graisser SILICON SILICONE...
  • Page 18 ADJUST NEEDLE / RÉGLER LE POINTEAU 3/4 Turn / 3/4 de tour NOTE: When needle is properly adjusted, trigger will move freely. REMARQUE: Si le pointeau est correctement réglé, la gâchette se manœuvre librement. 309045 1. Hold gun with nozzle straight up. Tenir le pistolet et la buse relevés complètement.
  • Page 19 4. Connect fluid hose, install tip and guard. Brancher le flexible produit, mettre en place la buse et la garde. Prime sprayer. See sprayer manual. Amorcer le pulvérisateur. Voir le manuel du pulvé- risateur. 6. Trigger gun into grounded metal bucket until fluid flows from gun.
  • Page 20 309045 8. Set trigger lock. Verrouiller la gâchette. 9. Try to trigger gun. No fluid should flow. Essayer d’actionner le pistolet. Le produit ne doit pas s’écouler. 10. If the gun fails either test, relieve pressure, disconnect hose and re- adjust needle, repeat tests.
  • Page 21 Notes 309045...
  • Page 22 Parts Drawing / Pièces 243011, A 243012, A 246506, A 309045 243012 & 246506 only 243012 & 246506 uni- quement Included with 1 Compris avec le repère 1 ti1432C...
  • Page 23: Parts List / Liste Des Pièces

    Parts List / Liste des pièces Ref. Part No. Description 243092 KIT, repair, gun, SG2/SG3 includes 9, 12, 13 218070 KIT, repair, gun SG3–E/SG3–A includes 9, 12, 13 GUARD, tip 237859 RAC IV (243011, 243012) 243161 RAC 5 (246506) 243639 TRIGGER, repair kit includes 32, 33 195495...
  • Page 24 Graco Standard Warranty Garantie standard de Graco Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from de- fects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.

This manual is also suitable for:

Sg2Sg3243011243012246506243238 ... Show all

GRACO MAGNUM 309045K INSTRUCTIONS MANUAL Pdf Download (2024)

FAQs

Can you use oil-based paint in Graco Magnum X5? ›

All Magnum sprayers can spray water-based and solvent-based paints, stains and primers that can be cleaned with mineral spirits. Materials that cannot be used with Magnum sprayers include solvent-based lacquers (exceptions are the ProX21 and the Pro210ES), texture based materials and elastomeric.

What is the minimum pressure for Graco X5? ›

Use Graco Replacement Parts Or Accessories That Are Rated A Minimum Of 3000 Psi. Always Engage The Trigger Lock When Not Spraying.

What should you use to flush the hose on an airless paint sprayer of oil based paint? ›

For flushing after spraying oil-based coatings, use compatible oil-based flushing fluid or mineral spirits.

Can I use Kilz in a paint sprayer? ›

KILZ® can be easily sprayed .

Can I leave paint in a Magnum X5 overnight? ›

Yes! We would happily leave paint in a sprayer for the day and even overnight if I was using it the following day. However, if you are finished spraying, give it a good clean and get it ready for storage.

Can paint be too thick for airless sprayer? ›

If the spray fans out evenly, the paint likely doesn't need thinning. If it sputters or leaves thick globs, it needs water to thin it. The best way to thin water-based latex paint is by adding water.

What pressure do I run my airless sprayer for interior painting? ›

How much pressure does a paint spray gun need? Airless sprayers will spray between 1200 to 2500 pounds per square inch (PSI) depending on the tip and paint you are using. To determine the best settings, perform a test spray starting with a lower pressure.

Is Magnum Project Painter Plus worth it? ›

Our Top Pick Overall - Graco Magnum Project Painter Plus

As far as sprayers for the DIYer go, Graco is a little pricier, but worth it if you plan on using it a lot. The Magnum Project Painter Plus is at a more obtainable price point, but uses the same airless tech that all of the Graco sprayers use.

What is the best Graco airless sprayer for home use? ›

Final Verdict. Our top recommendation is the Graco Magnum X5 Stand Airless Sprayer, which is an ideal choice for the typical small-to-medium painting projects taken on by DIYers. It lays down a very smooth coat of paint without excessive overspray, and it's easy to adjust the pressure.

Can you run oil-based paint through an airless sprayer? ›

Airless paint sprayers work with oil-based paint or stain. Typically, you shouldn't need to thin paint for an airless sprayer. HVLP paint sprayers work with oil-based paint. Thicker paints, such as water-based latex, can clog the sprayer.

Do you need to thin paint for Graco X5? ›

We did end up thinning it a little bit for some places, but there was really no need to at all....that was for our benefit of making the paint go a little farther. However, I will say that it took a lot less paint than it would have had we rolled or brushed. We were SO impressed with this little machine.

Can you use oil paint in a spray gun? ›

Yes, most modern paint sprayers can be used with oil-based paints, but it is still worth verifying with the manufacturer of the specific paint sprayer if this is possible.

Can you use a paint sprayer with oil-based stains? ›

I'm sharing how I stained my deck- turns out yes, yes you can use stain with a paint sprayer and it works amazing!

References

Top Articles
Latest Posts
Recommended Articles
Article information

Author: Reed Wilderman

Last Updated:

Views: 6725

Rating: 4.1 / 5 (52 voted)

Reviews: 91% of readers found this page helpful

Author information

Name: Reed Wilderman

Birthday: 1992-06-14

Address: 998 Estell Village, Lake Oscarberg, SD 48713-6877

Phone: +21813267449721

Job: Technology Engineer

Hobby: Swimming, Do it yourself, Beekeeping, Lapidary, Cosplaying, Hiking, Graffiti

Introduction: My name is Reed Wilderman, I am a faithful, bright, lucky, adventurous, lively, rich, vast person who loves writing and wants to share my knowledge and understanding with you.